Package Stops
View
Catalog Sheet  Buy
Package Stops Online  Print
This Page
Dead Type Stop
 |
Dead Type Package Stops are simply placed on bed section of gravity wheel and 1-3/8 in. roller conveyor. Styles A, B, or C can be used to lift or stop cartons or boxes. Easily attached to conveyor.
- 3 Styles
- 4 Widths
- 12 Ga. Steel
|
Angle End Stop
 |
Angle End Stop mounts to end of conveyor for stopping boxes, cartons, etc. Bolts to top flange of conveyor channels. Available in all standard conveyor widths.
- 1-1/2 in. x 1-1/2 in. x 12 ga. powder painted steel for: 190-LR, 138-ACC, 190-ACC, 138-NSP, 190-NSP, 190-ACZ, 1-3/8SR, SW, 19SR, 20SR
- 2 in. x 2 in. x 1/4 in. powder painted steel for 2-1/2 & 2-5/8 in gravity.
|
Raised End Roller
 |
Raised End Roller Stop can be mounted at end or
any desired location along conveyor (some drilling may be required). Steel angle brackets hold 2-1/8
in. dia. x 1/8 in. wall roller with 7/16 in. hex shaft. Bolts to top flange of conveyor channels. For
Models 190-LR, 138-ACC, 190-ACC, 190-ACZ, SW, 1-3/8SR, 19SR, & 20SR.
- Available in all standard widths
- Capacity: 150 lbs. live load capacity at 65 fpm
|
Hand Operated Blade/Roller
 |
Hand Operated Stops are used where manual line control is
required such as assembly work stations, shipping areas, etc. Can be mounted to underside of 190-LR, 138-ACC,
190-ACC, 138-NSP, 190-NSP, 190-ACZ, 1-3/8SR, 19SR & 20SR Conveyors.
CAPACITY–Blade 50 lbs. for 1-3/8 in. roller and 150 lbs. for 1.9 in. roller.
1-3/8 in. dia. roller 50 lbs., 1.7 in. dia. roller 150 lbs. All are live load
capacities at 65 FPM.
BEARINGS–Cam roller bearings to absorb impact.
OPERATION–Hand operated lever to raise or lower stop. Can be used
in normally up or down positions.
STOP–7 ga. formed angle 1 in. x 1-1/2 in. for 1-3/8 in. conveyors, 1-1/2
in. x 1-1/2 in. for 1.9 in. & 2.0 in. conveyors. Roller 1-3/8 in. dia. x 18
ga. galvanized steel for 1-3/8 in. conveyors. 1.7 in. dia. x 13
ga. unplated steel
roller for 1.9 in. & 2.0 conveyors.
STROKE–1-7/8 in. above rollers.
|
Foot Operated Blade/Roller
 |
Foot Operated Stops are used where manual line control is
required such as assembly work stations, shipping areas, etc.
Can be mounted to underside of SSR, 19SR, & 20SR Conveyors.
CAPACITY–Blade 50 lbs. for 1-3/8 in. roller and 150 lbs. for 1.9 in.
roller. 1-3/8 in. dia. roller 50 lbs., 1.7 in. dia. roller 150 lbs. All are live
load capacities at 65 FPM.
OPERATION–Foot operated lever to raise or lower stop.
STOP–Blade 1/4 in. steel plate, roller 1-3/8 in. dia. x 18
ga. galvanized
steel for 1-3/8 in. conveyors. 1.7 in. dia. x 13 ga. unplated steel
roller for 1.9 in. & 2.0 conveyors.
POSITION–Supplied normally down. Can be supplied normally up,
specify.
STROKE–2 in. above roller.
|
Air Operated Roller
 |
Air Operated Stops are used where automatic line control is
required such as assembly work stations, shipping areas, etc.
Can be mounted to underside of 190-LR, 138-ACC, 190-ACC, 190-NSP, 190-ACZ, SSR, 19SR, & 20SR Conveyors.
CAPACITY–1-3/8 in. dia. roller 50 lbs., 1.7 in. dia. roller 150 lbs. All are
live load capacities at 65 FPM.
BEARINGS–Cam roller bearings to absorb impact.
STOP–Roller—1-3/8 in. dia. x 18 ga. galvanized steel for 1-3/8 in.
conveyors. 1.7 in. dia. x 13 ga. unplated steel roller for 1.9 in. & 2.0 conveyors.
POSITION–Supplied normally down. Can be supplied normally up,
specify.
AIR CYLINDER–1-1/4 in. bore x 2 in. stroke double acting air cylinder
to raise or lower stop.
AIR REQUIREMENTS–Minimum pressure 60 P.S.I., maximum 125
P.S.I. Free air consumption at 60 P.S.I.–.014 cu. ft. per cycle, at 100
P.S.I.–.022 cu. ft.
VALVE–Single solenoid 4-way valve. 1/4 in.-20 NPT valve ports.
Electrical requirements are 120V 60 Hz. current draw , .161 amps.
INSTALLATION NOTE:–To eliminate contaminants in air supply line, a
filter, regulator should be installed prior to valve.
|
Linear Thruster Package Stop
 |
The Linear Thruster Package Stop is highly efficient and can be adapted to most any Hytrol powered roller or gravity conveyor.
|
|
